WTware Technical Support

It works good now, thanks!

Unfortunately that also doesn't work

aka wrote: ↑

Thu Apr 22, 2021 7:07 pm

Show me FULL all.log

I want to, but then I have to take a lot of photos.
It goes to CLI after the error message, web interface does not work.
I used less /tmp/all.log to view the log file.

Additional information from all.log:

[initrd] bootWay.cpp (132): -- ERROR -- Failed to mount /bootmedia
[initrd] bootWay.cpp (198): -- ERROR -- INTERAL ERROR. Please, contact WTware tech support.
[initrd] bootWay.cpp (251): -- ERROR -- INTERAL ERROR. Please, contact WTware tech support.

When I try to install WTware 6.0.46 from USB with UEFI, the following error is displayed:" ERROR: Failed to mount boot media. Please, send the photo of this screen to WTware techsupport and describe: where do you boot terminal from and what makes you think, that terminal can boot from it. It wo...

Hello, I have WTware UEFI installed. When I try to update WTware UEFI to the latest version and reboot, I always get the following error: photo In the full log after reboot there is this information: [ initrd] [ 3.510102] [FILE CACHE] Take 'packages/uefi-xnet' from cache. [ initrd] [ 3.530772] z.cpp...

Yes please return to wl driver.
B43 solves one issue, but creates many other issues.

Add to wpa_supplicant command line: -f /tmp/wpa_supplicant.out So we can compare wpa_supplicant output. This is the output Successfully initialized wpa_supplicant wlan0: CTRL-EVENT-REGDOM-CHANGE init=BEACON_HINT type=UNKNOWN wlan0: CTRL-EVENT-REGDOM-CHANGE init=BEACON_HINT type=UNKNOWN wlan0: CTRL-...

It there such line ? Yes, indeed it says [ 14.582103] b43 ssb0:0: firmware: direct-loading firmware b43/ucode16_mimo.fw [ 14.586401] b43 ssb0:0: firmware: direct-loading firmware b43/n0initvals16.fw [ 14.587283] b43 ssb0:0: firmware: direct-loading firmware b43/n0bsinitvals16.fw [ 16.262377] b43-ph...

After some testing, it seems that the Wi-Fi connection disconnects every minute or so. The following happens in the log: [ WPA] [ 263.881133] l2_packet_send - sendto: No buffer space available [ KERNEL] [ 263.884444] eth0: deauthenticating from bb:bb:bb:bb:bb:bb by local choice (Reason: 1=UNSPECIFIE...

Yes! It works! Broadcom is detected and B43 is loaded: [ initrd] [ 11.163418] [WiFi] Do not load wl for 14e4:432b. [ initrd] [ 11.194666] Found broadcom chip. [ initrd] [ 11.194777] modprobe b43. [ KERNEL] [ 11.228370] ssb: Found chip with id 0x4322, rev 0x01 and package 0x0A [ KERNEL] [ 11.341015] ...

Ah yes you are correct.
I needed to install debian again for lsmod output and it says that the b43 driver uses a non-free firmware.

Attached you can find the lsmod output.

Thanks, I attached the log to this reply. The unit does not support UEFI, so I can't install the WTware UEFI. I think this is the command I used on debian (nothing special): sudo wpa_supplicant -B -c /etc/wpa_supplicant.conf -i wlan0 The b43 driver (firmware-b43-installer) was the driver I used on d...

I tried wpa_supplicant on debian on the same terminal model with the Broadcom BCM4322 chipset and the latest Broadcom b43 driver. wpa_supplicant is there able to monitor the signal strength successfully. In the attached log you can see the wpa_supplicant log from the debian installation. So I think ...

We have multiple models of terminal touch screen. The log in my previous reply is from a model with an Intel Wi-Fi chipset. C 02:80 8086:24fd Network controller Network controller Intel Corporation Wireless 8265 / 8275 We have another model with a Broadcom BCM4322 Wi-Fi chipset. C 02:80 14e4:432b Ne...