WTware 5.8.66/RPi supervisor. [ KERNEL] [ 0.000000] Booting Linux on physical CPU 0x0 [ KERNEL] [ 0.000000] Linux version 4.19.73-v7 (aka@c22) (gcc version 8.3.0 (Debian 8.3.0-2)) #7 SMP Sun Sep 22 04:45:13 EDT 2019 [ KERNEL] [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d [ KERNEL] [ 0.000000] CPU: div instructions available: patching division code [ KERNEL] [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ KERNEL] [ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Rev 1.2 [ KERNEL] [ 0.000000] Memory policy: Data cache writealloc [ KERNEL] [ 0.000000] cma: Reserved 8 MiB at 0x3ac00000 [ KERNEL] [ 0.000000] On node 0 totalpages: 242688 [ KERNEL] [ 0.000000] Normal zone: 1896 pages used for memmap [ KERNEL] [ 0.000000] Normal zone: 0 pages reserved [ KERNEL] [ 0.000000] Normal zone: 242688 pages, LIFO batch:63 [ KERNEL] [ 0.000000] random: get_random_bytes called from 0x807009cc with crng_init=0 [ KERNEL] [ 0.000000] percpu: Embedded 15 pages/cpu s29132 r8192 d24116 u61440 [ KERNEL] [ 0.000000] pcpu-alloc: s29132 r8192 d24116 u61440 alloc=15*4096 [ KERNEL] [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ KERNEL] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240792 [ KERNEL] [ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1080 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 quiet wtboot=mmc [ KERNEL] [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ KERNEL] [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ KERNEL] [ 0.000000] Memory: 942060K/970752K available (5120K kernel code, 134K rwdata, 600K rodata, 5120K init, 349K bss, 20500K reserved, 8192K cma-reserved) [ KERNEL] [ 0.000000] Virtual kernel memory layout: [ KERNEL] [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ KERNEL] [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ KERNEL] [ 0.000000] vmalloc : 0xbb800000 - 0xff800000 (1088 MB) [ KERNEL] [ 0.000000] lowmem : 0x80000000 - 0xbb400000 ( 948 MB) [ KERNEL] [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ KERNEL] [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (6112 kB) [ KERNEL] [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (5120 kB) [ KERNEL] [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 135 kB) [ KERNEL] [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 350 kB) [ KERNEL] [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ KERNEL] [ 0.000000] rcu: Hierarchical RCU implementation. [ KERNEL] [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ KERNEL] [ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys). [ KERNEL] [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ KERNEL] [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ KERNEL] [ 0.000017] Switching to timer-based delay loop, resolution 52ns [ KERNEL] [ 0.000200] Console: colour dummy device 80x30 [ KERNEL] [ 0.000213] console [tty0] enabled [ KERNEL] [ 0.000250] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ KERNEL] [ 0.000263] pid_max: default: 32768 minimum: 301 [ KERNEL] [ 0.000412] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ KERNEL] [ 0.000426] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ KERNEL] [ 0.001029] CPU: Testing write buffer coherency: ok [ KERNEL] [ 0.001401] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ KERNEL] [ 0.001854] Setting up static identity map for 0x100000 - 0x10003c [ KERNEL] [ 0.001960] rcu: Hierarchical SRCU implementation. [ KERNEL] [ 0.002516] smp: Bringing up secondary CPUs ... [ KERNEL] [ 0.003137] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ KERNEL] [ 0.003820] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ KERNEL] [ 0.004446] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ KERNEL] [ 0.004535] smp: Brought up 1 node, 4 CPUs [ KERNEL] [ 0.004544] SMP: Total of 4 processors activated (153.60 BogoMIPS). [ KERNEL] [ 0.004548] CPU: All CPU(s) started in HYP mode. [ KERNEL] [ 0.004552] CPU: Virtualization extensions available. [ KERNEL] [ 0.005174] devtmpfs: initialized [ KERNEL] [ 0.016147] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4 [ KERNEL] [ 0.016495] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ KERNEL] [ 0.016511] futex hash table entries: 1024 (order: 4, 65536 bytes) [ KERNEL] [ 0.016942] pinctrl core: initialized pinctrl subsystem [ KERNEL] [ 0.017952] NET: Registered protocol family 16 [ KERNEL] [ 0.020154] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ KERNEL] [ 0.027511] bcm2835-mbox 3f00b880.mailbox: mailbox enabled [ KERNEL] [ 0.067809] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1 [ KERNEL] [ 0.070301] usbcore: registered new interface driver usbfs [ KERNEL] [ 0.070410] usbcore: registered new interface driver hub [ KERNEL] [ 0.070499] usbcore: registered new device driver usb [ KERNEL] [ 0.090374] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-09-12 16:32, variant start [ KERNEL] [ 0.100171] raspberrypi-firmware soc:firmware: Firmware hash is 4b30e8dcf91177a0be822c4c8d3bac8ed65f7ea5 [ KERNEL] [ 0.111845] clocksource: Switched to clocksource arch_sys_counter [ KERNEL] [ 0.124702] NET: Registered protocol family 2 [ KERNEL] [ 0.125254] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ KERNEL] [ 0.125285] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ KERNEL] [ 0.125392] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ KERNEL] [ 0.125577] TCP: Hash tables configured (established 8192 bind 8192) [ KERNEL] [ 0.125702] UDP hash table entries: 512 (order: 2, 16384 bytes) [ KERNEL] [ 0.125746] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ KERNEL] [ 0.125916] NET: Registered protocol family 1 [ KERNEL] [ 2.378715] Initialise system trusted keyrings [ KERNEL] [ 2.378874] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ KERNEL] [ 2.425571] Key type asymmetric registered [ KERNEL] [ 2.425581] Asymmetric key parser 'x509' registered [ KERNEL] [ 2.425694] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ KERNEL] [ 2.425707] io scheduler noop registered [ KERNEL] [ 2.425955] io scheduler cfq registered (default) [ KERNEL] [ 2.430493] bcm2708_fb soc:fb: FB found 1 display(s) [ KERNEL] [ 2.492394] Console: switching to colour frame buffer device 240x67 [ KERNEL] [ 2.527987] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 1920x1080 [ KERNEL] [ 2.530325] bcm2835-rng 3f104000.rng: hwrng registered [ KERNEL] [ 2.530764] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB) [ KERNEL] [ 2.531589] vc-sm: Videocore shared memory driver [ KERNEL] [ 2.535576] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000 [ KERNEL] [ 2.536981] zram: Added device: zram0 [ KERNEL] [ 2.538008] libphy: Fixed MDIO Bus: probed [ KERNEL] [ 2.538081] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ KERNEL] [ 2.566041] dwc_otg 3f980000.usb: base=(ptrval) [ KERNEL] [ 2.766263] Core Release: 2.80a [ KERNEL] [ 2.766274] Setting default values for core params [ KERNEL] [ 2.766300] Finished setting default values for core params [ KERNEL] [ 2.966589] Using Buffer DMA mode [ KERNEL] [ 2.966596] Periodic Transfer Interrupt Enhancement - disabled [ KERNEL] [ 2.966600] Multiprocessor Interrupt Enhancement - disabled [ KERNEL] [ 2.966609] OTG VER PARAM: 0, OTG VER FLAG: 0 [ KERNEL] [ 2.966644] Dedicated Tx FIFOs mode [ KERNEL] [ 2.967205] WARN::dwc_otg_hcd_init:1045: FIQ DMA bounce buffers: virt = bad04000 dma = 0xfad04000 len=9024 [ KERNEL] [ 2.967231] FIQ FSM acceleration enabled for : [ KERNEL] [ 2.967231] Non-periodic Split Transactions [ KERNEL] [ 2.967231] Periodic Split Transactions [ KERNEL] [ 2.967231] High-Speed Isochronous Endpoints [ KERNEL] [ 2.967231] Interrupt/Control Split Transaction hack enabled [ KERNEL] [ 2.967238] dwc_otg: Microframe scheduler enabled [ KERNEL] [ 2.967293] WARN::hcd_init_fiq:457: FIQ on core 1 [ KERNEL] [ 2.967304] WARN::hcd_init_fiq:458: FIQ ASM at 803b0750 length 36 [ KERNEL] [ 2.967315] WARN::hcd_init_fiq:497: MPHI regs_base at bb810000 [ KERNEL] [ 2.967335] dwc_otg 3f980000.usb: DWC OTG Controller [ KERNEL] [ 2.967371] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1 [ KERNEL] [ 2.967406] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000 [ KERNEL] [ 2.967454] Init: Port Power? op_state=1 [ KERNEL] [ 2.967458] Init: Power Port (0) [ KERNEL] [ 2.967635] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ KERNEL] [ 2.967647] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ KERNEL] [ 2.967655] usb usb1: Product: DWC OTG Controller [ KERNEL] [ 2.967662] usb usb1: Manufacturer: Linux 4.19.73-v7 dwc_otg_hcd [ KERNEL] [ 2.967670] usb usb1: SerialNumber: 3f980000.usb [ KERNEL] [ 2.968432] hub 1-0:1.0: USB hub found [ KERNEL] [ 2.968471] hub 1-0:1.0: 1 port detected [ KERNEL] [ 2.970791] dwc_otg: FIQ enabled [ KERNEL] [ 2.970798] dwc_otg: NAK holdoff enabled [ KERNEL] [ 2.970802] dwc_otg: FIQ split-transaction FSM enabled [ KERNEL] [ 2.970812] Module dwc_common_port init [ KERNEL] [ 2.972378] usbcore: registered new interface driver usbtouchscreen [ KERNEL] [ 2.973483] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ KERNEL] [ 2.973765] bcm2835-cpufreq: min=600000 max=1200000 [ KERNEL] [ 2.974512] sdhci: Secure Digital Host Controller Interface driver [ KERNEL] [ 2.974520] sdhci: Copyright(c) Pierre Ossman [ KERNEL] [ 2.975077] mmc-bcm2835 3f300000.mmcnr: could not get clk, deferring probe [ KERNEL] [ 2.975731] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe [ KERNEL] [ 2.975922] sdhci-pltfm: SDHCI platform and OF driver helper [ KERNEL] [ 2.976004] hidraw: raw HID events driver (C) Jiri Kosina [ KERNEL] [ 2.976528] usbcore: registered new interface driver usbhid [ KERNEL] [ 2.976535] usbhid: USB HID core driver [ KERNEL] [ 2.978927] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0 [ KERNEL] [ 2.980589] [vc_sm_connected_init]: start [ KERNEL] [ 2.991558] [vc_sm_connected_init]: end - returning 0 [ KERNEL] [ 2.992322] NET: Registered protocol family 17 [ KERNEL] [ 2.992474] Registering SWP/SWPB emulation handler [ KERNEL] [ 2.992781] Loading compiled-in X.509 certificates [ KERNEL] [ 2.994948] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0 [ KERNEL] [ 2.994956] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated [ KERNEL] [ 3.023506] sdhost: log_buf @ (ptrval) (fad07000) [ KERNEL] [ 3.059129] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ KERNEL] [ 3.060661] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ KERNEL] [ 3.062554] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ KERNEL] [ 3.065321] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ KERNEL] [ 3.071364] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1) [ KERNEL] [ 3.071542] of_cfs_init [ KERNEL] [ 3.071693] of_cfs_init: OK [ KERNEL] [ 3.115111] Freeing unused kernel memory: 5120K [ KERNEL] [ 3.154189] random: fast init done [ KERNEL] [ 3.176440] mmc0: host does not support reading read-only switch, assuming write-enable [ KERNEL] [ 3.179932] mmc0: new high speed SDHC card at address aaaa [ KERNEL] [ 3.180812] mmcblk0: mmc0:aaaa SC16G 14.8 GiB [ KERNEL] [ 3.182038] Indeed it is in host mode hprt0 = 00021501 [ KERNEL] [ 3.196307] mmc1: new high speed SDIO card at address 0001 [ KERNEL] [ 3.258954] Run /init as init process [ KERNEL] [ 3.263513] mmcblk0: p1 [ KERNEL] [ 3.401908] usb 1-1: new high-speed USB device number 2 using dwc_otg [ KERNEL] [ 3.402244] Indeed it is in host mode hprt0 = 00001101 [ hotplug] [ 3.454074] Block device 254:0. No action. [ hotplug] [ 3.573540] Block device 179:1. No action. [ hotplug] [ 3.573700] Block device 179:0. No action. [ pfac] [ 3.586696] Run /sbin/initrd. [ pfac] [ 3.586846] Ok, PID 652. [ initrd] [ 3.592028] WTware 5.8.66/RPi shell. [ initrd] [ 3.592471] Load font 'ter-c32b.psf', console 120x33. [ initrd] [ 3.638037] HDD/MMC/SD boot. [ KERNEL] [ 3.662059] usb 1-1: New USB device found, idVendor=0424, idProduct=9514, bcdDevice= 2.00 [ KERNEL] [ 3.662066] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ KERNEL] [ 3.662509] hub 1-1:1.0: USB hub found [ KERNEL] [ 3.662594] hub 1-1:1.0: 5 ports detected [ KERNEL] [ 3.981890] usb 1-1.1: new high-speed USB device number 3 using dwc_otg [ KERNEL] [ 4.112104] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00, bcdDevice= 2.00 [ KERNEL] [ 4.112115] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ KERNEL] [ 4.691881] usb 1-1.4: new full-speed USB device number 4 using dwc_otg [ KERNEL] [ 4.833705] usb 1-1.4: New USB device found, idVendor=24ae, idProduct=2010, bcdDevice= 1.10 [ KERNEL] [ 4.833716] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ KERNEL] [ 4.833725] usb 1-1.4: Product: Rapoo 2.4G Wireless Device [ KERNEL] [ 4.833733] usb 1-1.4: Manufacturer: RAPOO [ KERNEL] [ 4.840361] input: RAPOO Rapoo 2.4G Wireless Device as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:24AE:2010.0001/input/input0 [ KERNEL] [ 4.840846] hid-generic 0003:24AE:2010.0001: input,hidraw0: USB HID v1.10 Mouse [RAPOO Rapoo 2.4G Wireless Device] on usb-3f980000.usb-1.4/input0 [ KERNEL] [ 4.847952] input: RAPOO Rapoo 2.4G Wireless Device System Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:24AE:2010.0002/input/input2 [ KERNEL] [ 4.912470] input: RAPOO Rapoo 2.4G Wireless Device Consumer Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:24AE:2010.0002/input/input3 [ KERNEL] [ 4.913209] hid-generic 0003:24AE:2010.0002: input,hiddev96,hidraw1: USB HID v1.10 Device [RAPOO Rapoo 2.4G Wireless Device] on usb-3f980000.usb-1.4/input1 [ KERNEL] [ 4.917945] input: RAPOO Rapoo 2.4G Wireless Device as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.2/0003:24AE:2010.0003/input/input4 [ KERNEL] [ 4.993086] hid-generic 0003:24AE:2010.0003: input,hidraw2: USB HID v1.10 Keyboard [RAPOO Rapoo 2.4G Wireless Device] on usb-3f980000.usb-1.4/input2 [ initrd] [ 5.490934] Success: /dev/mmcblk0p1 mounted to /bootmedia. /--- FILE "/bootmedia/config.txt" ----------------------- | # For more options and information see: | # | # https://www.raspberrypi.org/documentation/configuration/config-txt/README.md | # | # Some settings may impact device functionality. See link above for details. | # Uncomment if you get no picture on HDMI for a default "safe" mode. | #hdmi_safe=1 | # Uncomment this if your display has a black border of unused pixels visible | # and your display can output without overscan. | disable_overscan=1 | # Uncomment if hdmi display is not detected and composite is being output. | #hdmi_force_hotplug=1 | # Uncomment to force a specific HDMI mode (this will force VGA). | #hdmi_group=1 | #hdmi_mode=1 | # Force the monitor to HDMI mode so that sound will be sent over HDMI cable. | #hdmi_drive=2 | # Uncomment to increase signal to HDMI, if you have interference, blanking, or | # no display. | #config_hdmi_boost=4 | # Uncomment to overclock the arm. 700 MHz is the default. | #arm_freq=800 | disable_splash=1 | #framebuffer_depth=32 | # Uncomment for 16-bit color. | framebuffer_depth=16 | # Enable onboard audio (HDMI or jack). | dtparam=audio=on | # Removes the warning overlay. | #avoid_warnings=1 | # Additionally allows turbo when low-voltage is present. | #avoid_warnings=2 | [pi4] | max_framebuffers=2 | [all] | # Uncomment these two lines to set display resolution: | #hdmi_group=2 | #hdmi_mode=58 | # | # Specify correct value in hdmi_mode= line from the list of valid values: | # 800x600: hdmi_mode=9 | # 1024x768: hdmi_mode=16 | # 1280x1024: hdmi_mode=35 | # 1360x768: hdmi_mode=39 | # 1400x1050: hdmi_mode=42 | # 1440x900: hdmi_mode=47 | # 1600x1200: hdmi_mode=51 | # 1680x1050: hdmi_mode=58 | # 1366x768: hdmi_mode=81 | # 1920x1080: hdmi_mode=82 | # 1920x1200: hdmi_mode=69 | # | # Find more resolutions in manual: | # https://www.raspberrypi.org/documentation/configuration/config-txt/video.md | # | # Uncomment six lines with such syntax and right hdmi_mode= values for | # dual displays on Raspberry Pi 4: | # | #[HDMI:0] | # hdmi_group=2 | # hdmi_mode=42 | #[HDMI:1] | # hdmi_group=2 | # hdmi_mode=58 | hdmi_group=2 | hdmi_mode=82 | framebuffer_depth=16 \---------------------------------------------------- [ initrd] [ 5.529534] Do not cache package files. [ initrd] [ 5.529783] WTpassword present: 29287a58bae30ae3ca8de202ec82b626. [ initrd] [ 5.598545] USB: 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter. [ initrd] [ 5.598676] USB: 0424:9514 Standard Microsystems Corp. SMC9514 Hub. [ initrd] [ 5.598734] USB: 24ae:2010 . /--- FILE "/bootmedia/configs/initrd.wtc" ----------------------- | clientIP = 192.168.168.194 | netmask = 255.255.255.0 | routerIP = 192.168.168.2 | nameserverIP = 192.168.168.107 | config = local | setupPassword = 29287a58bae30ae3ca8de202ec82b626 \---------------------------------------------------- [ initrd] [ 7.456001] Load Ethernet drivers. [ initrd] [ 7.456102] modprobe lan78xx. [ initrd] [ 7.461948] modprobe smsc95xx. [ KERNEL] [ 7.462901] usbcore: registered new interface driver lan78xx [ KERNEL] [ 7.469467] smsc95xx v1.0.6 [ KERNEL] [ 7.565041] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:20:67:1f [ KERNEL] [ 7.565375] usbcore: registered new interface driver smsc95xx [ KERNEL] [ 7.653695] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ KERNEL] [ 9.121098] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1 [ initrd] [ 9.155471] WTpassword present: 29287a58bae30ae3ca8de202ec82b626. [ pfac] [ 9.157422] Run /sbin/httpd. WTC listener is active. WTC broadcast listener is active. Send broadcast WTCU discover. [ pfac] [ 9.159405] Ok, PID 712. [ initrd] [ 9.159477] Run '/sbin/httpd', log '/tmp/httpd.out', env '', pid ''. [ initrd] [ 9.159617] Copy /bootmedia/configs/config.wtc to /tmp/config.wtc. [ initrd] [ 9.159900] Common local disk config: /--- FILE "/tmp/config.wtc" ----------------------- | [BOM] | server=192.168.168.109 | bpp=16 | connection \---------------------------------------------------- /--- FILE "/etc/config.compiled" ----------------------- | [BOM] | server=192.168.168.109 | bpp=16 | connection \---------------------------------------------------- [ initrd] [ 9.161939] Hostname: "wtwB827EB20671F". [ initrd] [ 9.162034] [NTP] 42 DHCP option is not set. Everyone can control terminal by RSH. RSH: listener is active. Send broadcast WTCU discover. [ httpd] [ 9.169250] Internal HTTP Server, WTware 5.8.66/RPi [ httpd] [ 9.177536] Reread settings. [ initrd] [ 9.177678] Unpack /bootmedia/packages/pi2-f. [ httpd] [ 9.177727] Everyone can control terminal by HTTP. [ KERNEL] [ 9.363719] random: crng init done [ gm] [ 9.365681] WTware 5.8.66/RPi session manager. [ gm] [ 9.366402] Add keyboard event3: RAPOO Rapoo 2.4G Wireless Device. [ gm] [ 9.366494] Add keyboard event2: RAPOO Rapoo 2.4G Wireless Device Consumer Control. [ gm] [ 9.366581] Add keyboard event1: RAPOO Rapoo 2.4G Wireless Device System Control. [ gm] [ 9.430125] EV_REL flag found. Add mouse event0: RAPOO Rapoo 2.4G Wireless Device. [ gm] [ 9.430436] Display mode: 1920x1080, 32 bit, landscape, 0 Hz, modeline "", DDC enabled, connector 0. [ gm] [ 10.000680] Framebuffer device found. [ gm] [ 10.000797] LINELENBYTES 7680 [ gm] [ 10.000859] VLEN 8294400 [ gm] [ 10.002874] Use /lib/ui32.so. [ gm] [ 10.095024] Run '/sbin/resolver 0x1f93d40 dns [192.168.168.109]', log '', env '', pid ''. [ pfac] [ 10.095339] Run /sbin/resolver 0x1f93d40 dns [192.168.168.109]. [ gm] [ 10.095399] Nobody can control terminal by VNC. [ pfac] [ 10.095651] Ok, PID 714. [ pfac] [ 10.100583] Process pid 714 terminated, status 00000000. [ gm] [ 10.107301] 192.168.168.109 => 192.168.168.109. [ gm] [ 10.115280] Free ram before fork terminal client /sbin/rdpclient (session 1): 922076 Kb. [ gm] [ 10.115371] Run '/sbin/rdpclient 1', log '/tmp/rdpclient.out', env '', pid ''. [ pfac] [ 10.115513] Run /sbin/rdpclient 1. [ pfac] [ 10.115697] Ok, PID 715. [ rdpclient 715] [ 10.123676] RDP Terminal Client, WTware 5.8.66/RPi, pipe 1, pid 715. [ rdpclient 715] [ 10.123989] Use /lib/ui32.so. [ rdpclient 715] [ 10.124917] Make RDP session with 192.168.168.109, port 3389. [ rdpclient 715] [ 10.125007] No username. [ rdpclient 715] [ 10.125086] No password. [ rdpclient 715] [ 10.125152] No PIN. [ rdpclient 715] [ 10.125193] No domain. [ rdpclient 715] [ 10.125234] No shell. [ rdpclient 715] [ 10.125274] No directory. [ rdpclient 715] [ 10.125314] Window: 1856x1080@24. [ rdpclient 715] [ 10.125354] PFlags 0x0000002F. [ rdpclient 715] [ 10.125394] Keyboard 00000409:00000000. [ rdpclient 715] [ 10.125436] My hostname "wtwB827EB20671F". [ rdpclient 715] [ 10.125476] TCP: connecting to 192.168.168.109:3389. [ rdpclient 715] [ 10.126960] TCP: connection with 192.168.168.109:3389 established. [ rdpclient 715] [ 10.127060] Turn keepalive on. [ rdpclient 715] [ 10.127903] Free ram after buffers allocation: 921296 KB. [ rdpclient 715] [ 10.134209] Process RDP server certificate. [ rdpclient 715] [ 10.134309] RDP5 encryption (X.509). [ rdpclient 715] [ 10.138841] Enable font smoothing. [ rdpclient 715] [ 10.200071] rdpclient-connect.cpp ( 2333): -- ERROR -- 16 24 [ rdpclient 715] [ 10.200207] Server requires 16 bit color depth. Windows Server is able to work with up to 32 bit color. But color depth can be limited by this parameter: Control Panel => Administrative tools => => Terminal services configuration => RDP-Tcp => => Client Settings => Maximum color depth Server allows to connect with any color depth only if this checkbox is turned off. cmd.exe with Administrator rights => gpedit.msc => Computer Configuration => Administrative Templates => Windows Components => Remote Desktop Services => Remote Desktop Session Host => Remote Session Environment => Limit maximum color depth => set to Enabled, Color Depth 32 bit. [ pfac] [ 10.201924] Process pid 715 terminated, status 00000009. [ gm] [ 10.202012] Final message: Server requires 16 bit color depth. Windows Server is able to work with up to 32 bit color. But color depth can be limited by this parameter: Control Panel => Administrative tools => => Terminal services configuration => RDP-Tcp => => Client Settings => Maximum color depth Server allows to connect with any color depth only if this checkbox is turned off. cmd.exe with Administrator rights => gpedit.msc => Computer Configuration => Administrative Templates => Windows Components => Remote Desktop Services => Remote Desktop Session Host => Remote Session Environment => Limit maximum color depth => set to Enabled, Color Depth 32 bit. [ gm] [ 21.827175] Run '/sbin/resolver 0x1f93d40 dns [192.168.168.109]', log '', env '', pid ''. [ pfac] [ 21.827351] Run /sbin/resolver 0x1f93d40 dns [192.168.168.109]. [ pfac] [ 21.827775] Ok, PID 716. [ pfac] [ 21.833311] Process pid 716 terminated, status 00000000. [ gm] [ 21.838726] 192.168.168.109 => 192.168.168.109. [ gm] [ 21.845048] Free ram before fork terminal client /sbin/rdpclient (session 2): 921332 Kb. [ gm] [ 21.845108] Run '/sbin/rdpclient 2', log '/tmp/rdpclient.out', env '', pid ''. [ pfac] [ 21.845154] Run /sbin/rdpclient 2. [ pfac] [ 21.845337] Ok, PID 717. [ rdpclient 717] [ 21.853546] RDP Terminal Client, WTware 5.8.66/RPi, pipe 2, pid 717. [ rdpclient 717] [ 21.853835] Use /lib/ui32.so. [ rdpclient 717] [ 21.854772] Make RDP session with 192.168.168.109, port 3389. [ rdpclient 717] [ 21.854899] No username. [ rdpclient 717] [ 21.854946] No password. [ rdpclient 717] [ 21.854991] No PIN. [ rdpclient 717] [ 21.855036] No domain. [ rdpclient 717] [ 21.855079] No shell. [ rdpclient 717] [ 21.855122] No directory. [ rdpclient 717] [ 21.855164] Window: 1856x1080@24. [ rdpclient 717] [ 21.855208] PFlags 0x0000002F. [ rdpclient 717] [ 21.855248] Keyboard 00000409:00000000. [ rdpclient 717] [ 21.855289] My hostname "wtwB827EB20671F". [ rdpclient 717] [ 21.855330] TCP: connecting to 192.168.168.109:3389. [ rdpclient 717] [ 21.855879] TCP: connection with 192.168.168.109:3389 established. [ rdpclient 717] [ 21.855963] Turn keepalive on. [ rdpclient 717] [ 21.856872] Free ram after buffers allocation: 920552 KB. [ rdpclient 717] [ 21.863082] Process RDP server certificate. [ rdpclient 717] [ 21.863168] RDP5 encryption (X.509). [ rdpclient 717] [ 21.867538] Enable font smoothing. [ rdpclient 717] [ 21.925702] rdpclient-connect.cpp ( 2333): -- ERROR -- 16 24 [ rdpclient 717] [ 21.925843] Server requires 16 bit color depth. Windows Server is able to work with up to 32 bit color. But color depth can be limited by this parameter: Control Panel => Administrative tools => => Terminal services configuration => RDP-Tcp => => Client Settings => Maximum color depth Server allows to connect with any color depth only if this checkbox is turned off. cmd.exe with Administrator rights => gpedit.msc => Computer Configuration => Administrative Templates => Windows Components => Remote Desktop Services => Remote Desktop Session Host => Remote Session Environment => Limit maximum color depth => set to Enabled, Color Depth 32 bit. [ gm] [ 21.926238] Final message: Server requires 16 bit color depth. Windows Server is able to work with up to 32 bit color. But color depth can be limited by this parameter: Control Panel => Administrative tools => => Terminal services configuration => RDP-Tcp => => Client Settings => Maximum color depth Server allows to connect with any color depth only if this checkbox is turned off. cmd.exe with Administrator rights => gpedit.msc => Computer Configuration => Administrative Templates => Windows Components => Remote Desktop Services => Remote Desktop Session Host => Remote Session Environment => Limit maximum color depth => set to Enabled, Color Depth 32 bit. [ pfac] [ 21.927466] Process pid 717 terminated, status 00000009. [ gm] [ 23.539153] Run '/sbin/resolver 0x1f93d40 dns [192.168.168.109]', log '', env '', pid ''. [ pfac] [ 23.539305] Run /sbin/resolver 0x1f93d40 dns [192.168.168.109]. [ pfac] [ 23.539767] Ok, PID 718. [ pfac] [ 23.545335] Process pid 718 terminated, status 00000000. [ gm] [ 23.550895] 192.168.168.109 => 192.168.168.109. [ gm] [ 23.556895] Free ram before fork terminal client /sbin/rdpclient (session 3): 920244 Kb. [ gm] [ 23.556952] Run '/sbin/rdpclient 3', log '/tmp/rdpclient.out', env '', pid ''. [ pfac] [ 23.556996] Run /sbin/rdpclient 3. [ pfac] [ 23.557181] Ok, PID 719. [ rdpclient 719] [ 23.565375] RDP Terminal Client, WTware 5.8.66/RPi, pipe 3, pid 719. [ rdpclient 719] [ 23.565660] Use /lib/ui32.so. [ rdpclient 719] [ 23.566797] Make RDP session with 192.168.168.109, port 3389. [ rdpclient 719] [ 23.566933] No username. [ rdpclient 719] [ 23.566985] No password. [ rdpclient 719] [ 23.567030] No PIN. [ rdpclient 719] [ 23.567078] No domain. [ rdpclient 719] [ 23.567121] No shell. [ rdpclient 719] [ 23.567168] No directory. [ rdpclient 719] [ 23.567209] Window: 1856x1080@24. [ rdpclient 719] [ 23.567251] PFlags 0x0000002F. [ rdpclient 719] [ 23.567293] Keyboard 00000409:00000000. [ rdpclient 719] [ 23.567336] My hostname "wtwB827EB20671F". [ rdpclient 719] [ 23.567377] TCP: connecting to 192.168.168.109:3389. [ rdpclient 719] [ 23.567947] TCP: connection with 192.168.168.109:3389 established. [ rdpclient 719] [ 23.568014] Turn keepalive on. [ rdpclient 719] [ 23.568816] Free ram after buffers allocation: 920244 KB. [ rdpclient 719] [ 23.575472] Process RDP server certificate. [ rdpclient 719] [ 23.575561] RDP5 encryption (X.509). [ rdpclient 719] [ 23.580239] Enable font smoothing. [ rdpclient 719] [ 23.641345] rdpclient-connect.cpp ( 2333): -- ERROR -- 16 24 [ rdpclient 719] [ 23.641465] Server requires 16 bit color depth. Windows Server is able to work with up to 32 bit color. But color depth can be limited by this parameter: Control Panel => Administrative tools => => Terminal services configuration => RDP-Tcp => => Client Settings => Maximum color depth Server allows to connect with any color depth only if this checkbox is turned off. cmd.exe with Administrator rights => gpedit.msc => Computer Configuration => Administrative Templates => Windows Components => Remote Desktop Services => Remote Desktop Session Host => Remote Session Environment => Limit maximum color depth => set to Enabled, Color Depth 32 bit. [ gm] [ 23.641852] Final message: Server requires 16 bit color depth. Windows Server is able to work with up to 32 bit color. But color depth can be limited by this parameter: Control Panel => Administrative tools => => Terminal services configuration => RDP-Tcp => => Client Settings => Maximum color depth Server allows to connect with any color depth only if this checkbox is turned off. cmd.exe with Administrator rights => gpedit.msc => Computer Configuration => Administrative Templates => Windows Components => Remote Desktop Services => Remote Desktop Session Host => Remote Session Environment => Limit maximum color depth => set to Enabled, Color Depth 32 bit. [ pfac] [ 23.643028] Process pid 719 terminated, status 00000009.